Fusion Series
FS-1600D-10GE

JAI's FS-1600D-10GE is a 2-CMOS multispectral prism camera providing simultaneous images of different spectral bands in a single camera - a visible color channel from 400-670 nm and a near infrared (NIR) channel from 740-1000 nm. This makes it possible to simultaneously inspect surface properties and sub-surface defects. A backwards-compatible 10 GigE interface provides exceptional speed and networking flexibility.

Product Image FS 1600 D T 10 GE front 45 degree 410x370px

Product Image FS 1600 D T 10 GE Rear 45 degree 410x370px

Product Image FS 1600 D T 10 GE front view 410x370px

Product Image FS 1600 D T 10 GE side view 410x370px

Simultaneous color and near infrared (NIR) imaging

The visible light channel outputs RGB or Bayer color images spanning the wavelengths visible to the human eye. The NIR channel, on the other hand, “sees” below the surface of organic and other materials to detect imperfections the human eye cannot see.

Replaces multiple inspection stations with a single setup

JAI’s prism technology ensures perfect two-channel alignment, allowing users to replace multiple inspection stations with a single setup, providing both ease of use and lower equipment and maintenance costs.

Individual exposure time adjustment for each channel

Separate exposure control for each channel allows the channels to be adjusted to one another without changes in the gain – maintaining a consistent signal-to-noise ratio at all times.

Features
Specifications
Downloads
Accessories

Features

Prism-based 2-CMOS multispectral area scan camera that simultaneously captures visible and near-IR light.
Backwards-compatible 10GBASE-T (10 GigE) interface auto-negotiates to match the speed of connected equipment including NBASE-T (5 GigE and 2.5 GigE) and standard 1 Gbps 1000BASE-T GigE Vision.
Sequence trigger mode for on-the–fly change of gain, exposure and ROI.
Supports IEEE 1588 Precision Time Protocol for synchronization in multi-camera applications.
Color output can be raw Bayer (8/10/12-bit) or 24/30-bit RGB using 5x5 in-camera interpolation.
Dual-stream output enables color and NIR images to be simultaneously output over a single cable.
Color Enhancer and Edge Enhancer functions included.
Single- and multi-ROI modes.
20 percent better NIR sensitivity than previous CCD models.

Specifications

Product Line

Fusion Series

Model

FS-1600D-10GE

Type

Area Scan

Color / Mono

Multispectral

Light Spectrum

2-Bands Visible + NIR

Resolution

1.6 MP

Resolution WxH

1440 x 1080 px

Frame rate / Line rate

226 fps

ROI

Yes

Interface

10 Gbps GigE Vision

Sensors

2xCMOS (Vis/NIR)

Sensor Name

IMX273

Optical Format

1/2.9 inch

Cell Size WxH

3.45 x 3.45 µm

Shutter type

Global shutter

Sensor Diagonal

6.2 mm

Active Sensor Dimensions WxH

5.0 x 3.7 mm

Camera Dimensions HxWxL

62 x 62 x 86.5 mm

Weight

270 g

Video Output

8/10/12-bit *

Lens Mount

C-mount

Power Consumption

10.4 Watt

Operating Temperature (ambient)

-5°C to +45°C

* Some video processing functions not available with 12-bit output

Downloads

Manual & datasheet

Software

Compliance documents

PD-12 Power Supply

A universal power supply that works with all JAI cameras equipped with a 12-pin Hirose power connector. Four versions are available:

PD-12UUP U.S. plug with 12-pin Hirose connector to camera

PD-12UEP European plug with 12-pin Hirose connector to camera

PD-12UU U.S. plug, flying leads (no 12-pin connector)

PD-12UE European plug, flying leads (no 12-pin connector)

Download Datasheet

PC-12P Hirose 12-pin Connector

The HR10A-10P-12S is a universal connector used for power and control signals for many JAI cameras. The connector is a female plug, with sockets, that mates to the connector on the back of the camera. It has soldering cups for easy assembly of custom cables.

MP-41 Tripod Mounting Plate

Tripod adapter for Fusion Series cameras and some discontinued models with 40 mm spacing between mounting holes.

Only use the supplied M3 screws having the proper length. Using longer screws can damage internal circuit boards.

10P-10M-AUX Auxiliary TTL cable

The 10P-10M-AUX is 10-meter cable for JAI cameras equipped with a 10-pin Hirose “auxiliary” connector. The plug at one end of the cable connects to the 10-pin connector on the back of the JAI camera. Flying leads at the other end of the cable can be used to send/receive TTL signals to/from specific pins on the auxiliary connector. Not all I/O functions may be supported depending on the pinout of each camera model. Check the pinout carefully or consult with JAI before purchasing.

Download a datasheet

Here are a few applications where Fusion Series industrial cameras are especially suitable.

The Fusion Series cameras are the perfect starting point for a wide range of machine vision applications.

Inspection of nuts, almonds and olives

The color, size, shape and damage nuts and almonds can be inspected using the RGB channel, while foreign objects (including olive pits) are more clearly seen with the NIR channel

Electronics inspection

Inspection of stuffed PCB boards including traces, solder, component placement/alignment, shorting, and other items where color and NIR inspection is important.

2D print inspection

Color inspection of magazines and pharmaceutical packaging as well as currency inspection looking at color correctness, water marks and security features woven into bank notes.

LCD display

Surface inspection of flat panels/displays looking for scratches and defective screen pixels.

Adding value to artificial intelligence in farming

Precision agriculture or intelligent farming has seen an exponential growth in the recent years. Removal of weeds or wild plants is of growing importance in intelligent farming.

Fruit and vegetable inspection

Fruit and vegetable inspection simultaneous looking at colors, ripeness, damages, signs of rot under skin, as well as detecting foreign objects (e.g. stones, metal pieces etc.)

Find the perfect machine vision camera to meet your application requirements.

Get advice from our camera experts.